I haven't installed any license on router, switch, and fw before and always wanted to know the steps to install it Go to Solution. This document explains how to do it on most routers its generally the same but commands can vary between routers and switch platforms ,it talks about the PAK product activation key too you get when you buy your license off your Cisco reseller and a link of how to use itonce installed in your flash or bootflash depending on device its few basic steps to follow to activate it.

To install a permanent license, perform the steps detailed in this section. View solution in original post. Order a license through normal Cisco sales channels and processes. Note: if your order was placed through a partner, you may need to contact your partner to obtain a copy of this email. Register the PAK at www. Buy or Renew.

cisco license activation

Find A Community. We're here for you! Turn on suggestions. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Showing results for. Search instead for. Did you mean:. The procedure to install license. Hi, I haven't installed any license on router, switch, and fw before and always wanted to know the steps to install it Would you please provide me how to install the license from A to Z? How can I get the license first of all? Thank you in advance! Labels: Other Switching. Accepted Solutions. Mark Malone. VIP Mentor. Order a license through. Mark, Thank you so much! How and where can I get the license?

Do I have to purchase it from vendor? How will they give me the license? Thru email? Thank you so much abache!!Before you start setting up your device, create a place and a digit activation code on Control Hub.

Read here how to Generate an Activation Code for a Device. The device is shipped with preinstalled software, and updates are installed automatically.

To find out more about software updates, see: Automatic software updates. Install and plug in the needed cables according to the installation guide instructions. When the device is plugged in, it automatically starts up and checks the network connection. If the network connection works, the device checks for updates of Webex RoomOS and installs any new versions it finds. If there is an issue with the connection, you see an error message that suggests a possible cause. After the software update, the setup wizard starts.

Follow the on-screen instructions to set up network preferences, enter the activation code, and to check the screen, camera, and sound. To change the language settings, you can do this before you start the setup wizard, or afterward from the Settings menu. The time format follows your network's time zone setting and can't be configured separately.

Stay connected with the people you need, without traveling. Skip To Content Help Center. English en-us. Popular help topics:.

Before you begin. Was this article helpful? Yes No. Thanks for the feedback! Comments or suggestions? We're sorry this page did not help.

How can we improve? Is this about? Product e. Webex, Jabber etc. This Article. This Website.A PAK file is normally received via email after the purchase of license s and normally in the form of a PDF attachment. Recommend to contact Licensing team at licensing cisco. After receiving the license key file via email, please consult below knowledge base link for further information and guidance:.

Skip to content Skip to footer. Available Languages. Download Options. Updated: July 14, Contents Introduction. Click on to ' Continue to Product License Registration ' button. Enter the PAK number and ' Submit '. Click the ' Actions ' drop down box.

Select ' Get New Licenses '. Please see below for example: Click on ' Next ' button from the next screen. Enter the serial number of the appliance. Please enter the serial number of the appliance after the ' - ' sign. Enter the correct ' Send To ' email address to receive the license key file.

Enter the ' End User ' information for this request. Once submitted, a confirmation page will be displayed. Please allow at least 30 minutes for the license key file to be sent to the ' Send To ' email address.

Issue experience during the PAK file registration Recommend to contact Licensing team at licensing cisco. Next step after receiving the license key file After receiving the license key file via email, please consult below knowledge base link for further information and guidance: How to install feature keys on a Cisco Email or Web Security Appliance. Contributed by Cisco Engineers Handy Putra.

Was this Document Helpful? Yes No Feedback. Related Cisco Community Discussions.What should I do after I purchase a license? How to activate a Cisco license? Some users who bought a Cisco license may be not clear that how to activate the Cisco license.

Here, we will share the easy tips and steps of acting your Cisco license. Note: There are two methods of PAK delivery. The first is a paper certificate sent via standard postal carrier. The second, and more efficient method, is to select eDelivery for electronic delivery of the PAK. Select this option, when available and it will save a lot of time in shipment. Serial no.

Depending on the product, this could either be the device serial number, MAC address, etc. Please refer to the product documentation to verify the appropriate UDI information for your device. You may also need to supply the hostname of the unit, your email address, and the physical address of the device.

cisco license activation

It is very important to make sure you can get the license file finally. Many other licensing activities can be accomplished through the online portal, too. This includes registering a new license, rehosting a license due to RMA, and applying for a temporary or demo license. There is a FAQ document and video also available from the website for additional best practices.

If you are unable to perform the licensing activity online, the Global Licensing Operation GLO team can provide assistance. There are 3 ways to open a case with GLO:. Each of these has pros and cons, but we definitely encourage customers to use the website whenever possible and to call us whenever necessary.

Using the website is truly the optimal method for non-urgent issues. The first two methods can also be used to contact TAC to reach an engineer. Below items you need to prepare: a. How to Activate a Cisco License?

More Steps: 1. Fill in the PAK, and submit. More TIPS you can get while activating your Cisco license: Many other licensing activities can be accomplished through the online portal, too. This is the preferred method and the most efficient method for customers to open severity 3 service requests. The second is by calling in the US and Canada. This should be used for urgent situations such as a network down or severe degradation to reach someone quickly.

Lastly, is to email GLO at licensing cisco. Share This Post.I wonder if someone can help me find the exact license -s I have on my router, and especially help me find what is the currently enabled max throughput, and whether I need to buy a license to extend it.

If it isn't m, and if I wanted to extend it to m, would I need to pay, or just configure some more lines on the router? I am extremely confused as per what all the columns mean, if someone could shed some light in detail on how to read the output, it would be greatly appreciated.

Go to Solution. View solution in original post. If you issue "sh ver" the router will show you what feature licenses are installed and permanent. As for throughput, I don't think the series throughput is license based. So, you get all the throughput the device can offer with any license. License to change the bandwidth applies to ASR series. But I am afraid the throughput does depend on licenses; I would like to know on WHICH license, and from my outputs, is it possible to understand what license was bought and enabled on the device, and therefore understand what is the allowed throughput?

It's time to sign up for a Smart Account

As for license, you have IP base and security which gives you all the packages in figure-1 in this link:. The problem is that " show license feature" does not show you the base throughput numbers but the other command I provided does.

Which command does help to get the details to validate the license? I have to identify the difference between temp and permanent. Buy or Renew. Find A Community. We're here for you!

Turn on suggestions. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type. Showing results for. Search instead for.When you activate software from a Cisco device, you can license software without the need for additional application software. Your software release may not support all the features documented in this module.

For the latest caveats and feature information, see Bug Search Tool and the release notes for your platform and software release. To find information about the features documented in this module, and to see a list of the releases in which each feature is supported, see the feature information table. Use Cisco Feature Navigator to find information about platform support and Cisco software image support.

To access Cisco Feature Navigator, go to www. An account on Cisco. For the stackable switches that support the Cisco IOS Software Activation feature, one switch must act as primary and the others as secondaries. The primary switch performs management and administrative operations on itself as well as on the secondary switches. If you use Microsoft Entourage and receive the license file from Cisco in an e-mail attachment, the license file will contain UTF-8 marking.

These extra bytes in the license file cause it to be unusable during license installation. To work around this issue, you can use a text editor to remove the extra characters and then install the license file.

The installation process does not install duplicate licenses. This message appears when duplicate licenses are detected:. The PAK is provided to you when you order or purchase the right to use a feature set for a particular platform.

9.2 IOS Licensing (CCNA3: Chapter 9: IOS Images and Licensing)

The PAK serves as a receipt and is used as part of the process to obtain a license. You need the UDI of the device as part of the process to obtain a license. After entering the appropriate information, you will receive an e-mail containing the license information that you can use to install the license:.

Copy the license file received from the Cisco Product License Registration portal to the appropriate file system on the device.

Click the Install button on the web page. A reload is not required when moving from an evaluation license to a permanent license of the same license level on ASR routers. Only on Cisco Catalyst E switch platforms If a switch number is specified, this command is executed on the specified switch.

When the license is present in license storage and multiple license lines are stored, you are prompted to select a license line. To select the license, type the number at the Select Index to Add Comment prompt. If the device is a switch, this command obtains statistics from the specified switch. Saves copies of all licenses in a device and stores them in a format required by the command in the specified storage location. Saved licenses are restored by using the license install command.

Use the? Optional switch switch-num : sends this request to a specific switch in a switch stack.

cisco license activation

Before you can start the rehost or resend process, a device credential is required. Cisco software licensing requires that the license files generated by the Cisco back-end licensing system for its devices be secure and tamper-resistant. Security features are in place to authenticate a license by means of encrypted license credentials.

If it becomes necessary to transfer a license from one device to another which is called rehostinga permission ticket is required.

To generate the permission ticket, the Cisco back-end licensing system requires the device credential information.I haven't installed any license on router, switch, and fw before and always wanted to know the steps to install it Go to Solution. This document explains how to do it on most routers its generally the same but commands can vary between routers and switch platforms ,it talks about the PAK product activation key too you get when you buy your license off your Cisco reseller and a link of how to use itonce installed in your flash or bootflash depending on device its few basic steps to follow to activate it.

To install a permanent license, perform the steps detailed in this section. View solution in original post. Order a license through normal Cisco sales channels and processes.

Note: if your order was placed through a partner, you may need to contact your partner to obtain a copy of this email. Register the PAK at www. Buy or Renew. Find A Community. We're here for you! Turn on suggestions. Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.

Cisco IOS Software Activation

Showing results for. Search instead for. Did you mean:. The procedure to install license. Hi, I haven't installed any license on router, switch, and fw before and always wanted to know the steps to install it Would you please provide me how to install the license from A to Z? How can I get the license first of all? Thank you in advance! Labels: Other Switching. Accepted Solutions. Mark Malone. VIP Mentor.

Software Activation Configuration Guide, Cisco IOS Release 15M&T

Order a license through. Mark, Thank you so much! How and where can I get the license? Do I have to purchase it from vendor?


Replies to “Cisco license activation”

Leave a Reply

Your email address will not be published. Required fields are marked *